ECU Cloning – Engine Control Unit Data Transfer

We transfer all data from your failed ECU to a tested donor unit in Riga, Latvia – immobilizer, keys, firmware, calibrations. Faster and more affordable than dealer replacement

Price: from €100 incl. VAT

Check availability for your vehicle

Enter plate number or select your car manually

LV
or select manually ▼
Searching...
Vehicle not found in databaseSelect manually from the list above
Installment payment available via KLIX
Get a quote
We'll calculate the exact price for your vehicle
optional
Sending...
KLIX Pay in installments, no overpayment
✓
Thank you!
We'll call back with the price for your vehicle
Mon–Fri   9:30 – 17:00 | Sat: 10:00 – 15:00 (by appointment)

Why you need ECU cloning

01

A dead ECU does not mean buying new from the dealer

When your engine control unit fails from water ingress, short circuits, or internal damage, the dealer offers only one option: a brand-new unit at premium cost. ECU cloning transfers all your data to a tested used donor – your vehicle runs identically, but you save significantly compared to OEM replacement.

02

Complete data transfer – immobilizer, keys, firmware

During cloning we copy the entire ECU contents: FLASH firmware, EEPROM data, immobilizer pairing, key codes, VIN, PIN, injector codes, and all learned adaptations. The donor becomes an exact replica of your original unit – your car starts with the same keys as if nothing changed.

03

Your chip tuning stays intact

If your vehicle had chip tuning – Stage 1, Stage 2, DPF or EGR delete – all modified calibrations transfer to the donor unit. You do not need to re-flash or pay for tuning again. Every map, boost table, and error mask carries over precisely.

04

Faster turnaround than ordering a new ECU

Ordering a new ECU from the dealer can take weeks – shipping, programming, key synchronization. We complete cloning within a single working day when a donor is available. Your vehicle returns to the road without prolonged downtime.

05

All makes and models supported

We clone ECUs for any vehicle – BMW, Mercedes, Audi, VW, Volvo, Land Rover, Jaguar, and more. Our KESS3 and KTAG equipment supports all major processor and memory types used in modern engine control units.

ECU cloning process

01

Diagnostics and assessment

We connect Launch X431 to identify the root cause of ECU failure and read all accessible data. We assess whether the original unit contents can be extracted and determine the exact part number for donor selection.

02

Reading data from the original ECU

Using KESS3 or KTAG, we read a full dump of the failed ECU – FLASH firmware and EEPROM: immobilizer data, key codes, VIN, PIN, injector codes, adaptations, and calibrations. We use bench or boot mode depending on the unit condition.

03

Donor unit selection and verification

We source a compatible used ECU by matching the part number and hardware revision. The donor is tested for full functionality – we read its contents and verify memory and processor integrity before proceeding.

04

Cloning process

We write the complete original ECU contents into the donor – both FLASH and EEPROM. Every byte is verified in WinOLS by comparing the original dump against the cloned unit. We confirm all data transferred correctly before moving forward.

05

Installation and final testing

We install the cloned ECU in your vehicle and verify communication with every system – immobilizer, ABS, airbags, instrument cluster. The engine starts, runs through all operating modes, and we confirm zero fault codes across every module.

What you get

Failed engine control unit replaced with a working donor

your vehicle is back on the road

All data transferred

immobilizer, keys, VIN, injector codes, learned adaptations

Car starts with the original keys

no additional key programming required

Chip tuning preserved

all calibrations and modifications carried over without loss

Significant savings compared to purchasing a new ECU from the dealer

Our equipment

KESS3 (Alientech)

ECU reading and writing tool supporting OBD, bench, and boot mode. We extract the complete FLASH and EEPROM dump from the failed unit and write it to the donor – all data including immobilizer, keys, and calibrations.

KTAG (Alientech)

Bench programmer for direct microprocessor, EEPROM, and FLASH memory access. Used when OBD access is not possible – severe physical damage to the unit or locked ECUs that block standard communication.

WinOLS

Professional firmware editor for post-cloning data verification. We compare the donor contents against the original dump byte-by-byte to confirm all maps, calibrations, and settings transferred correctly.

Launch X431

Diagnostic platform for initial ECU failure assessment and final post-installation verification. We read fault codes, test communication between all control modules, and confirm system-wide functionality.

Sound familiar?

Engine control unit has failed – car will not start, no communication with the ECU

ECU damaged by water or fluid ingress – corrosion and internal short circuits

Dealer quotes an expensive new unit – you need a cost-effective alternative

You purchased a used ECU but the car will not start – immobilizer is not synchronized

ECU bricked after a failed reflash attempt – locked, unresponsive, no communication

You need to transfer data from the old ECU to a new unit while preserving chip tuning

FAQ

ECU cloning at JVK PRO in Riga costs from €100 including VAT. The exact price depends on the make, engine and scope of work – we confirm it before starting, by plate number or after diagnostics. Pay-later with KLIX is available.

You have two options: buy a new ECU from the dealer or clone your data onto a used donor unit. Cloning transfers everything – immobilizer pairing, key codes, firmware, adaptations – to a compatible working ECU. The result is identical, but the cost is significantly lower.

Yes. We read the complete dump from your failed ECU – FLASH and EEPROM – and write it to a donor unit with a matching part number. After cloning, the donor becomes an exact copy of your original engine control unit.

Yes. We transfer the full memory contents – including modified calibrations, injection and boost maps, error masks. If your vehicle had Stage 1, DPF or EGR delete – everything carries over to the donor unit without any loss.

We work with all major brands – BMW, Mercedes, Audi, VW, Volvo, Land Rover, Jaguar, Porsche, and others. Our KESS3 and KTAG equipment covers all mainstream ECU processor and memory types.

Typically one working day when a donor unit is available. Data extraction and writing take 2 to 4 hours, final verification and testing about one more hour. If we need to source a compatible donor, that may require additional time.

Yes. We guarantee correct data transfer and donor unit functionality after installation. If any issues arise with the cloned ECU, we resolve them at no additional cost within the warranty period.

Reflashing modifies the software on an existing ECU – for example, chip tuning or error correction. Cloning is a complete data copy from one physical unit to another – including immobilizer, keys, VIN, and all settings. Cloning is required when the original unit is physically damaged beyond repair.

ECU failed? We clone it – faster and cheaper than replacement

Complete data transfer to a donor unit – immobilizer, keys, firmware, chip tuning. Plug and play, no dealer visit needed

+371 22 11 11 16
Piedrujas iela 28, Rīga
Mon-Fri: 9:30 – 17:00

Book ECU Clone

Stated figures are approximate. Results depend on vehicle condition and driving circumstances.