ECU Firmware Recovery and Flash Verification

We read, analyze, and restore your engine control unit software – professional ECU diagnostics in Riga, Latvia

Price: from €130 incl. VAT

Check availability for your vehicle

Enter plate number or select your car manually

LV
or select manually ▼
Searching...
Vehicle not found in databaseSelect manually from the list above
Installment payment available via KLIX
Get a quote
We'll calculate the exact price for your vehicle
optional
Sending...
KLIX Pay in installments, no overpayment
✓
Thank you!
We'll call back with the price for your vehicle
Mon–Fri   9:30 – 17:00 | Sat: 10:00 – 15:00 (by appointment)

Why you need ECU recovery

01

Standard diagnostics cannot detect firmware-level issues

OBD scanners read fault codes, but they cannot evaluate whether the calibration maps inside your ECU are correct. We go deeper – analyzing the actual firmware data to find the real cause.

02

We fix what a bad tune broke

If a previous tuner modified the wrong maps or applied an incompatible file, we identify every altered calibration table and either revert it or rewrite it properly.

03

Factory restore or professional correction – your choice

Depending on your goals, we flash the original firmware back or apply a clean, verified remap that stays within safe engine parameters.

04

Data-driven analysis in WinOLS – no guesswork

Every ECU file is opened in WinOLS and compared map-by-map against the stock original. We see exactly what was changed – fueling, boost pressure, ignition timing, lambda targets.

05

All vehicle makes and ECU types supported

BMW, Mercedes, Audi, VW, Volvo, Land Rover, Toyota, Hyundai – our hardware and expertise cover European, Asian, and specialty ECU platforms.

ECU recovery process

01

Full OBD diagnostic scan

We read all fault codes and live data streams with Launch X431 to understand the current state before touching the firmware.

02

ECU firmware extraction

Using KESS3 or AutoTuner, we read the current flash file from the engine control unit – via OBD port or direct bench connection.

03

Calibration analysis in WinOLS

The extracted file is loaded into WinOLS and compared against the known stock version. Every modified map is flagged and evaluated.

04

Firmware restoration or correction

Based on the analysis, we either write back the original factory firmware or apply precise corrections to the damaged calibration tables.

05

Verification and road test

After flashing, we perform a full test drive, monitor live engine data, and confirm that all parameters are within factory specifications.

What you get

Root cause of the ECU issue identified with precision

Factory-original firmware successfully restored

Bad or incompatible tune corrected and verified

Engine parameters confirmed within safe operating range

Vehicle ready for reliable daily driving

Our equipment

KESS3 (Alientech)

Professional-grade ECU read/write tool supporting OBD, bench, and boot modes – compatible with over 500 ECU types across all major manufacturers.

FLEX / AutoTuner

Versatile flash tools for direct ECU connection in bench and boot mode, used when OBD access is restricted or unavailable.

WinOLS

Industry-standard calibration analysis platform for comparing map data, detecting modifications, and applying precise corrections to ECU firmware files.

Launch X431

Multi-brand diagnostic scanner for reading fault codes, monitoring live data streams, and actuator testing before and after firmware changes.

Sound familiar?

Your car runs rough or throws new fault codes after a chip tune or ECU remap

Fuel consumption has increased noticeably with no obvious mechanical cause

New warning lights or error codes appeared after a software change that diagnostics cannot resolve

The engine hesitates, jerks, or does not respond to throttle input the way it used to

Noticeable power loss – the car no longer pulls like it did before the remap

Unusual exhaust smoke – black, blue, or white – that was not present before the tune

FAQ

ECU firmware check and restoration at JVK PRO in Riga costs from €130 including VAT. The exact price depends on the make, engine and scope of work – we confirm it before starting, by plate number or after diagnostics. Pay-later with KLIX is available.

Common signs include unstable idle, increased fuel consumption, power loss, or new fault codes after a remap. If your car feels different since the tune – it is worth checking.

Yes. In most cases we read the firmware through the OBD port – no disassembly required. Only in rare situations do we need direct bench access to the ECU module.

Bring it in for an ECU flash check. We will extract the firmware, compare it against the factory original, identify exactly what was changed incorrectly, and fix it.

The inspection and analysis typically take 1–2 hours. If restoration is needed, the total process may take 2–4 hours depending on the ECU complexity.

Yes. We guarantee that the restored or corrected firmware will meet factory-spec parameters and the vehicle will run stable. Any follow-up issues are resolved at no extra cost.

In most cases – yes. We maintain access to original firmware databases. If the stock file is available, we flash it directly. If not, we reconstruct it using reference maps in WinOLS.

Yes – petrol, diesel, and hybrid. We cover European brands (BMW, Mercedes, Audi, VW, Volvo), Asian brands (Toyota, Hyundai, Kia), and other popular makes in Latvia.

Not sure about your ECU firmware?

We will inspect it, identify the problem, and fix it – professionally and without risk. Book your ECU flash check in Riga today.

+371 22 11 11 16
Piedrujas iela 28, Rīga
Mon-Fri: 9:30 – 17:00

Book Original Restore

Pay later

Don't want to pay now? Purchase online – pay later!

Go to payment
Secure payment via KLIX by Citadele
Stated figures are approximate. Results depend on vehicle condition and driving circumstances.